Siding Calculator
Courses, pieces and squares for a wall from its dimensions, the openings and the board exposure you set.
What the siding calculator does
It counts the courses and pieces a wall needs and the squares its net area is ordered in. Courses = ceil(wall height / board exposure), pieces per course = ceil(wall length / stock length), and the pieces are their product. A 12 m by 2.7 m wall with 3 m² of openings, 150 mm of exposure and 3.6 m boards is 18 courses of 4 pieces, which is 72 pieces, and a 10 % allowance brings the order to 80.
The net area is the gross area minus the openings, 29.4 m², and the squares line applies the waste to that area and divides by 9.290304 m², because a square is 100 square feet. Both halves are printed so the piece count and the area order can be compared.
Gable ends, trim, a starter strip and the corners are not counted, and the page does not choose a colour or a profile. The waste allowance is yours, from 0 to 50 %.
Figures print to up to four decimal places with trailing zeros trimmed.
How to use it
Set Wall length and Wall height in metres, then type the total of Doors and windows in square metres.
Set Board exposure to the visible height of one course, set Stock board length from the boards you are buying, and set Waste.
Press Run. The result prints the net area, the courses, the pieces per course, the pieces to order, the board metres and the squares.
Worked example
Input with the defaults:
Wall 12 × 2.7 m, 3 m² openings, exposure 0.15 m, stock 3.6 m, 10 % waste
Output:
Net area: 29.4 m²
Courses: 18 (ceil(2.7 ÷ 0.15))
Pieces: 72 (18 courses × 4)
Squares: 3.481 (net area + waste ÷ 9.290304 m²)
Why it runs in your browser
The courses, pieces and squares are computed in this tab. Your wall's dimensions are never uploaded.
The page counts the siding courses a wall needs from the exposure you are setting: one course per exposure height, one board per stock length, and the product is the piece count. A 12 m wall at 2.7 m with 150 mm of exposure and 3.6 m boards is 18 courses of 4 pieces, which is 72 pieces before the waste allowance.
The net wall area after the doors and windows is printed beside the count, together with the squares that area is ordered in, because siding is bought both by the piece and by the square.
Gable ends, trim and a starter strip are outside the count, and the page says so rather than implying a complete envelope take-off.
Exposure is the number that decides the count
The exposure is the visible height of one course, which is the board's face width minus the overlap the profile needs. A 200 mm board lapped 50 mm exposes 150 mm, and that 150 mm is what divides the wall height. Using the board's full width instead is the common error, and it under-counts the courses.
Because exposure is a control, the same wall can be compared at two lap depths without re-measuring anything. The page prints the exposure it used with the courses, so the two readings cannot be confused.
Squares, pieces and the difference between them
A square is 100 square feet, or 9.290304 m², and it is the unit a siding order is often counted in. The square figure here is the net wall area plus the waste, divided by that constant; it is not derived from the piece count, so the two lines can differ slightly at the edges.
The piece count answers a different question: how many boards of your stock length to buy. A course that ends in a 0.6 m cut still costs a whole board in this count, which is why the two figures sit side by side.
How to use Siding Calculator
Set Wall length and Wall height in metres, then type the total of Doors and windows in square metres.
Set Board exposure to the visible height of one course and Stock board length to the boards you are buying, then set Waste.
Press Run. The result prints the net area, the courses, the pieces per course, the pieces to order, the board metres and the squares.
What to Expect
Best for
- Ordering siding boards and squares for a measured wall
- Comparing two exposures on the same wall
- Checking a contractor's piece count against the area
Not ideal for
- Gable ends, which are triangles the page does not model
- A rain-screen or a panel system with its own layout rules
- Trim, corners, a starter strip and the fixings
What this tool keeps
- The wall, opening, exposure and stock dimensions you typed
- The net area and the courses, so both lines can be checked
What may need cleanup
- A wall measured in feet, which has to be converted to metres
- An exposure taken from a board's full width rather than its lap
Common errors
- Using the board width as the exposure instead of the visible face
- Forgetting the openings, which makes the area and the squares too high
Example use cases
- Ordering cladding for a shed or a house wall
- Budgeting a siding replacement by square
- Checking how much an extra 20 mm of exposure saves
Sample input
Wall 12 × 2.7 m, 3 m² of openings, exposure 0.15 m, stock 3.6 m, 10 % waste.
Sample output
29.4 m² net, 18 courses, 72 pieces, 80 to order, 3.481 squares.
Who this is for
- Anyone ordering siding for a measured wall
- A builder checking a take-off in squares
Frequently asked questions
What is exposure, and why is it not the board width?
Exposure is the visible height of a course after the lap. A 200 mm board lapped 50 mm exposes 150 mm, and 150 mm is what divides the wall height. Typing the full width would under-count the courses.
Why are pieces and squares both printed?
They answer different purchase questions. Pieces count whole stock boards, so a short cut still costs a board; squares measure the net area in 9.290304 m² units. A supplier may quote either, so both are on the page.
Are the windows and doors subtracted?
Yes, the openings you type are subtracted from the gross wall area before the net area and the squares are computed. The piece count still covers the courses that run past an opening, because a board is cut rather than omitted.
Does it include gable ends?
No. A gable is a triangle and the page works in rectangles. Measure the gable's area separately and add it to the net area, or treat it as a second wall with its own height.
Build custom tools for your store
Join the SDK program to create useful ecommerce utilities for your store.