Decking Calculator screenshot

Decking Calculator

Board rows, stock boards and board metres for a deck, from the board and gap you are laying.

Privacy First
0 Runs
Updated 2026-11-21
Runs in your browser
No sign-up, no upload

What the decking calculator does

It counts the board rows a deck needs and the stock boards those rows cost. There is one row per board width plus gap: rows = ceil(deck width / (board width + gap)), and each row is ceil(deck length / stock length) boards. A 4 m by 2.4 m deck with 140 mm boards, a 5 mm gap and 2.4 m stock is 17 rows of 2 boards, which is 34 boards, and a 10 % allowance brings the order to 38.

The board metres line is the order multiplied by the stock length, 91.2 m, so the figure can be compared with a quote. Offcuts are not carried from one row into the next: reusing a 1.6 m offcut is a decision about the board, not arithmetic, so the page prints the conservative count.

Fixings, joists, a picture-frame border and stairs are not counted, and the page says so rather than implying a complete take-off. The waste allowance is yours, from 0 to 50 %.

Figures print to up to four decimal places with trailing zeros trimmed.

How to use it

Set Deck length and Deck width to the deck's outside dimensions in metres.

Set Board width, the Gap between boards and the Stock board length from the boards you are buying, then set Waste to the allowance you buy for.

Press Run. The result prints the rows, the boards per row, the boards before waste, the boards to order and the board metres.

Worked example

Input with the defaults:

Deck 4 × 2.4 m, board 0.14 m, gap 0.005 m, stock 2.4 m, 10 % waste

Output:

Rows:          17 (ceil(2.4 ÷ 0.145))
Boards:        34 (17 rows × 2)
With waste:    38 boards
Board metres:  91.2 m (38 × 2.4)

Why it runs in your browser

The rows and the board metres are computed in this tab. Your deck's dimensions are never uploaded.

The page counts the board rows a deck needs from the board you are laying: one row per board width plus gap, rounded up, and one stock board per length of the deck. A 4 m by 2.4 m deck, 140 mm boards, a 5 mm gap and 2.4 m stock comes to 17 rows of 2 boards, which is 34 boards before the waste allowance.

The board metres line is printed beside the count, so the order can be compared with a quote, and the waste percentage is a control rather than a hidden constant.

Offcuts are not carried from one row into the next. Reusing a part board is a decision about the board and the look of the deck, not arithmetic, so the page prints the conservative count and says so.

The two ceilings this page does not compute

A deck has two limits that this page cannot see: the board's span rating, which decides the joist spacing, and the joist and footing design, which decides whether the deck can hold what you put on it. Both are structural questions with a manufacturer's table and a local code behind them, and neither is arithmetic on the board you typed.

What the page does answer is the purchase: how many boards, in what length, with what allowance. That is why it prints the board metres as well as the board count — a supplier sells both, and a quote usually names the metre figure.

Gap, picture frame and stairs

The gap is part of the pitch, not an afterthought: 140 mm boards with a 5 mm gap repeat every 145 mm, which is what turns a 2.4 m width into 17 rows rather than 18. A wider gap means fewer boards and more drainage, and the page takes the number you are actually laying.

A picture-frame border runs around the deck and is counted in linear metres rather than rows, so it is not included. Stairs, fascia and the screws are not included either. The page states all three rather than implying a complete take-off.

How to use Decking Calculator

Set Deck length and Deck width to the outside dimensions of the deck you are building, in metres.

Set Board width, the Gap between boards and the Stock board length from the boards you are buying, then set Waste to the allowance you buy for.

Press Run. The result prints the rows, the boards per row, the boards before waste, the boards to order and the board metres.

What to Expect

Best for

  • Turning a deck's dimensions into a board order
  • Checking a supplier's board count against your own layout
  • Comparing a 140 mm board with a 145 mm one at the same gap

Not ideal for

  • A board's span rating or a joist layout, which are structural questions
  • A diagonal or herringbone pattern, which wastes more than the rows here
  • Stairs, fascia, a border and the fixings

What this tool keeps

  • The deck, board and gap dimensions you typed
  • The rows and the boards per row, so the count can be followed

What may need cleanup

  • A deck measured in feet, which has to be converted to metres first
  • A board quoted in inches, which has to become metres before it is entered

Common errors

  • Entering the board width and forgetting the gap in the pitch
  • Expecting the page to carry offcuts between rows

Example use cases

  • Ordering composite or timber decking boards
  • Budgeting a deck rebuild by board metres
  • Checking why a supplier's count is higher than the area suggests

Sample input

Deck 4 × 2.4 m, board 0.14 m, gap 0.005 m, stock 2.4 m, 10 % waste.

Sample output

17 rows of 2 boards, 34 boards before waste, 38 to order, 91.2 board metres.

Who this is for

  • Anyone ordering decking boards for a known footprint
  • A carpenter checking a take-off before a quote

Frequently asked questions

Why does the gap change the number of boards?

The boards repeat at a pitch of board width plus gap, so a 5 mm gap makes a 140 mm board occupy 145 mm of deck width. A wider gap means fewer rows across the same width, and the page uses the gap you type rather than a default.

Why are offcuts not reused between rows?

They can be, and a joiner often will. Reusing a 1.6 m offcut is a decision about the board's joints and the look of the deck, so the page counts each row as whole stock boards and prints the conservative order instead of guessing.

Does this check that my joists are close enough?

No. A board's span rating depends on its material, thickness and the joist spacing, and it is a manufacturer's table rather than arithmetic. This page counts boards for a deck you have already designed.

What does the waste percentage cover?

The cut boards at the edges, a damaged board and the spare a job usually keeps. It is applied to the board count and rounded up, and the metres line is computed from the rounded count so the two agree.

Developer program

Build custom tools for your store

Join the SDK program to create useful ecommerce utilities for your store.