Backsplash Calculator screenshot

Backsplash Calculator

Counter length times backsplash height, less openings, plus waste, counted in tile boxes.

Privacy First
0 Runs
Updated 2026-11-21
Runs in your browser
No sign-up, no upload

What the backsplash calculator does

It computes the wall area behind the counter, subtracts the openings you name, adds waste and divides by the coverage of one box: area = counter length × height; net = area − openings; with waste = net × (1 + waste ÷ 100); boxes round up.

The openings figure is a total area — a window, an outlet cut-out or a gap behind an appliance — and it is yours to supply, because the page cannot see the wall. The box coverage is the figure printed on the tile box. Both are printed back so the order can be checked.

In the sample a 3 m counter with a 0.5 m backsplash is 1.5 m2; 0.2 m2 of openings leaves 1.3 m2; 10 % waste makes 1.43 m2; at 1 m2 per box that is 2 boxes.

A part box counts as a whole box. The page is ordering arithmetic, not a tile layout: it does not place cuts, grout lines or trim pieces, and the basis line says so. Openings that are not smaller than the wall area, a coverage of zero and a waste allowance above 50 % are each refused by name.

How to use it

Set Counter length, Backsplash height, Openings, Coverage per box and Waste.

Press Run. The result prints the backsplash area, the net area, the area with waste and the box count.

Worked example

Input with the defaults:

3 m counter, 0.5 m high, 0.2 m2 openings, 1 m2 per box, 10 % waste

Output:

Backsplash area:       1.5 m2 (3 × 0.5)
Less openings:         1.3 m2
With waste:            1.43 m2 (10 %)
Boxes:                 2 × 1 m2

Why it runs in your browser

The arithmetic runs in this tab. Your measurements are never uploaded.

The page multiplies the counter length by the backsplash height, subtracts the openings you name, adds waste and divides by the coverage of one box.

Openings and box coverage are controls, and the result prints both so the order can be checked against the wall and the tile box.

Wall area, not tile layout

Area = counter length × height, less the openings you name, plus waste, divided by the box coverage. The page prints the gross area, the net area, the area with waste and the box count, so a disagreement can be traced to one step.

It does not place cuts, grout lines or trim pieces. Those decide how much of a box is usable and how the pattern breaks at a corner, and a page that pretended to model them would be less honest than one that stops at the area.

How to use Backsplash Calculator

Set Counter length, Backsplash height, Openings, Coverage per box and Waste.

Press Run. The result prints the backsplash area, the net area, the area with waste and the box count.

What to Expect

Best for

  • Ordering tile for a kitchen backsplash
  • Checking a box count against a label coverage
  • Comparing two backsplash heights

Not ideal for

  • A pattern layout with cuts and trim
  • A wall with several windows whose openings are not measured yet
  • A price, which needs a tile rate the page does not take

What this tool keeps

  • Every dimension, opening and coverage you typed
  • The waste percentage applied

What may need cleanup

  • Openings measured per outlet rather than as a total area
  • Coverage given in square feet, which must be converted first

Common errors

  • Subtracting openings after adding waste
  • Using the floor tile's coverage for a wall tile

Example use cases

  • Ordering a kitchen backsplash
  • Checking a tiler's box count
  • Planning a laundry splashback

Sample input

A 3 m counter, a 0.5 m height, 0.2 m2 of openings, 1 m2 per box and 10 % waste.

Sample output

A 1.5 m2 backsplash, 1.3 m2 net, 1.43 m2 with waste and 2 boxes.

Who this is for

  • Homeowners planning a splashback
  • Tilers checking an order

Frequently asked questions

Why does 1.43 m2 need two boxes of 1 m2?

A part box is a box you have to buy, so 1.43 rounds up to 2. The box coverage is printed beside the count, so a different product changes the answer.

Should openings be subtracted before or after waste?

Before. An opening is wall you will not tile, so it comes out of the area first; waste then applies to what you install. The page prints the net area and the area with waste separately.

Does the page allow for cuts and pattern matching?

Only through the waste allowance you set. The page does not place cuts or match a pattern; a large-format tile or a strong pattern needs a larger allowance, and that is your figure to choose.

Developer program

Build custom tools for your store

Join the SDK program to create useful ecommerce utilities for your store.