Bike Gear Ratio Calculator screenshot

Bike Gear Ratio Calculator

Turn chainring and cog teeth into a gear ratio, the distance one crank revolution covers, and the speed at a given cadence.

Privacy First
0 Runs
Updated 2026-11-22
Runs in your browser
No upload
Deterministic
Formula stated

What this page does

The gear ratio is chainring teeth divided by cog teeth; multiplying by the wheel's circumference gives the metres one crank revolution covers, and cadence turns that into speed.

How to use it

Enter this sample with the defaults shown:

50

Press Run. The page gives:

Chainring:     50 teeth
Cog:           16 teeth
Gear ratio:    3.125 : 1
Development:   6.5625 m per crank revolution
Speed:         35.4375 km/h at 90 rpm
Basis:         wheel circumference 2100 mm, cadence held constant

The formula and its basis

Gear ratio = chainring teeth ÷ cog teeth. Development = ratio × wheel circumference in metres. Speed in km/h = development × cadence × 60 ÷ 1000.

Teeth and cadence are whole numbers as entered; the wheel circumference is the mounted tyre's, in millimetres. Ratios print to four decimals and intermediate values are never rounded.

What it is not

This page is arithmetic on the numbers you enter, with each assumption stated: it is not financial, medical or training advice, and nothing is uploaded, stored or logged.

The gear ratio is chainring teeth divided by cog teeth; multiplying by the wheel's circumference gives the metres one crank revolution covers, and cadence turns that into speed.

The rule this page applies: Gear ratio = chainring teeth ÷ cog teeth. Development = ratio × wheel circumference in metres. Speed in km/h = development × cadence × 60 ÷ 1000.

Basis: Teeth and cadence are whole numbers as entered; the wheel circumference is the mounted tyre's, in millimetres. Ratios print to four decimals and intermediate values are never rounded.

Worked example: the sample values below, with the defaults, give exactly the output recorded in What to Expect.

How to use the Bike Gear Ratio Calculator

Enter chainring teeth in the box, set the options beside it, then press Run. The answer appears beside the form and re-runs on the same input.

Every number in the answer follows from your inputs and the assumptions stated below; the page does not choose a rate for you.

The worked example uses "50" with the defaults shown, and its exact output is printed in What to Expect.

The formula, its basis and its refusals

Gear ratio = chainring teeth ÷ cog teeth. Development = ratio × wheel circumference in metres. Speed in km/h = development × cadence × 60 ÷ 1000.

Teeth and cadence are whole numbers as entered; the wheel circumference is the mounted tyre's, in millimetres. Ratios print to four decimals and intermediate values are never rounded. Money prints to two decimals, percentages and ratios to four, and intermediate values are never rounded.

It refuses zero teeth, a wheel circumference outside 500 to 3000 mm, and a cadence outside 0 to 250 rpm.

What this page is not

It is arithmetic on the numbers you enter, with each assumption stated. It is not a training prescription, a medical measurement or a health-risk assessment, and it does not replace a coach or a clinician.

Where the tool is the wrong choice: Drivetrain efficiency, which the page does not model; A full gear-inch table.

What to Expect

Best for

  • Comparing a compact and a standard chainset
  • Checking the top gear's speed at a cadence
  • Choosing a cassette for a hilly route

Not ideal for

  • Drivetrain efficiency, which the page does not model
  • A full gear-inch table

What this tool keeps

  • The numbers exactly as you entered them
  • The same answer on every run
  • Nothing sent, stored or logged

What may need cleanup

  • Units mixed between fields: enter kilograms and centimetres as each label says
  • A comma used as a decimal separator, which the page refuses by name

Common errors

  • It refuses zero teeth, a wheel circumference outside 500 to 3000 mm, and a cadence outside 0 to 250 rpm.
  • A non-numeric value, which the page names rather than silently treating as zero

Example use cases

  • Working out how fast a gear rolls at 90 rpm
  • Comparing two cassettes

Sample input

50

Sample output

Chainring: 50 teeth Cog: 16 teeth Gear ratio: 3.125 : 1 Development: 6.5625 m per crank revolution Speed: 35.4375 km/h at 90 rpm Basis: wheel circumference 2100 mm, cadence held constant

Who this is for

  • Cyclists and bike fitters

Frequently asked questions

What formula does this page use?

Gear ratio = chainring teeth ÷ cog teeth. Development = ratio × wheel circumference in metres. Speed in km/h = development × cadence × 60 ÷ 1000.

What does it refuse?

It refuses zero teeth, a wheel circumference outside 500 to 3000 mm, and a cadence outside 0 to 250 rpm.

What does this page not do?

It is arithmetic on the numbers you enter, with each assumption stated. It is not a training prescription, a medical measurement or a health-risk assessment, and it does not replace a coach or a clinician.

What rate basis and rounding does it use?

Teeth and cadence are whole numbers as entered; the wheel circumference is the mounted tyre's, in millimetres. Ratios print to four decimals and intermediate values are never rounded. Money prints to two decimals, percentages and ratios to four, and intermediate values are never rounded.

What is development?

The distance the bike travels in one crank revolution: gear ratio × wheel circumference. It is the number that makes two gears comparable across wheel sizes.

Where do I find the wheel circumference?

From the tyre's mounted circumference, or by rolling the bike one revolution and measuring. A 700×25 tyre is about 2100 mm.

Developer program

Build custom tools for your store

Join the SDK program to create useful ecommerce utilities for your store.