Thermal Expansion Calculator
Compute the length, area and volume change of an isotropic solid from its coefficient of linear expansion and a temperature change.
Length, area and volume from one coefficient
Enter the coefficient of linear expansion in units of 10⁻⁶/K — 23 for aluminium, for instance — the original length in metres, and the temperature change in kelvin. The page evaluates ΔL = α·L₀·ΔT and prints the growth in millimetres, then applies the isotropic identities ΔA/A = 2α·ΔT and ΔV/V = 3α·ΔT to give the fractional area and volume change. Fifty kelvin on one metre of aluminium grows it 1.15 mm.
The identities hold for an isotropic solid — the same α in every direction — and a crystal with a strongly anisotropic coefficient will not follow them. The coefficient is taken as constant over the range, which is an approximation, and a change of phase or a constrained part that builds stress is outside the model. A negative or zero coefficient is refused, because a material that shrinks on heating is not what this formula describes.
The arithmetic runs in this tab from the three numbers you type. Nothing is uploaded, no material is stored, and the same values print the same expansion after a reload.
The general isotropic expansion from a coefficient you supply: ΔL = α·L₀·ΔT, then ΔA/A = 2α·ΔT and ΔV/V = 3α·ΔT. Enter α in units of 10⁻⁶/K — 23 for aluminium — with a length in metres and a change in kelvin.
The area and volume identities hold for an isotropic solid with the same coefficient in every direction. A crystal with a strongly anisotropic coefficient, or a material that changes phase, is outside the model.
How to use it
Type the coefficient in 10⁻⁶/K, the original length in metres and the temperature change in kelvin, then press Run. The page prints the length change in millimetres, the multiplication behind it, and the fractional area and volume changes.
The arithmetic
The coefficient is multiplied by 10⁻⁶ once to reach 1/K, then used three times: once for the length, twice for the area share and three times for the volume share. Those factors come from the isotropic identities, not from measuring the part.
Where it stops
The page does not model anisotropy, a constrained part, a phase change, or a coefficient that varies with temperature. A coefficient of zero or below is refused, because the formula describes a solid that grows on heating and a shrinking material needs a negative coefficient the page will not accept silently.
What to Expect
Best for
- Checking length, area and volume change from one coefficient.
- Comparing two coefficients over the same temperature step.
What this tool keeps
- The coefficient and dimensions are computed in the browser and never posted, so the page works offline and retains nothing.
Sample input
α = 23×10⁻⁶/K, 1 m, 50 K
Sample output
ΔL = 1.15 mm ΔL = α·L₀·ΔT = 2.3e-5 /K × 1 m × 50 K ΔA/A = 2α·ΔT = 0.0023, ΔV/V = 3α·ΔT = 0.00345
Frequently asked questions
How do I use it?
Enter the coefficient in 10⁻⁶/K, the original length in metres and the temperature change in kelvin, then press Run. Length, area and volume changes are printed in one block.
Is anything uploaded?
No. The arithmetic runs in this tab with JavaScript: no request is made, no account is needed, nothing is stored, and the page keeps working offline once loaded.
What are its limits?
The coefficient must be positive and the solid isotropic; a constrained part, a phase change or a strongly anisotropic crystal must not be read from these fractional changes.
Build custom tools for your store
Join the SDK program to create useful ecommerce utilities for your store.