SMD Resistor Code Calculator screenshot

SMD Resistor Code Calculator

Decode SMD resistor codes like 103 into ohm values.

Privacy First
0 Runs
Updated 2026-11-07
Runs in your browser
No upload
No account needed
Updates as you type

Decode SMD resistor codes like 103 into ohm values. Enter your numbers and get an instant result.

Type the marking printed on a surface-mount resistor and the page decodes it: three-digit and four-digit codes use their last digit as a power of ten, a letter R marks a decimal point, and a two-digit-plus-letter code is read from the EIA-96 table.

The decoded value is shown in ohms and in a shortened form, with kΩ above one thousand and MΩ above one million, trimmed to at most two decimal places. A drawing of the chip repeats the code so you can check you typed what is on the part.

The page reports the standard it matched — 3-digit, 4-digit, EIA-96 or a decimal form — but it does not check that the value is a stocked E-series part. A code can decode arithmetically and still name a resistance nobody manufactures.

How each code shape is read

In a three-digit code the first two digits are the significant figures and the third is the multiplier, so 103 is 10 followed by three zeros, or 10 kΩ. A four-digit code uses three significant figures and a fourth multiplier digit, so 1002 is 100 followed by two zeros, or 10 kΩ as well.

An EIA-96 code is two digits from a 96-entry table plus a letter for the multiplier, so 01C is 100 times 100, or 10 kΩ. A code containing R is a decimal value: 4R7 is 4.7 Ω and 1R2 is 1.2 Ω.

  • 3 digits: two figures times ten to the third digit
  • 4 digits: three figures times ten to the fourth digit
  • EIA-96: two digits from the table, one multiplier letter

Where a decode can mislead

The same printed code can mean different things on different part families, and some manufacturers use their own schemes for very small packages. The page decodes the three standard shapes above and refuses anything else with a sentence rather than guessing.

A leading zero is significant in the EIA-96 form because the two digits index the table, while leading zeros in a plain numeric code are dropped by the arithmetic. Read the standard field before trusting the number when the part is unfamiliar.

How to use the decoder

Type the marking into the SMD Marking Code field, exactly as printed, or press one of the preset samples such as 103, 4R7 or 01C to see a known decode. The value, the shortened kΩ or MΩ form, and the matched standard appear as you type, with the code redrawn on the chip drawing.

Compare the drawing with the part in your hand before trusting the number: the echo shows what the page read, not what the manufacturer printed. When the page refuses a code, the part uses a scheme outside the three standard shapes.

What to Expect

Best for

  • Decoding a code you can read but cannot identify
  • Checking a value against a schematic before soldering
  • Learning the difference between 3-digit and EIA-96 markings

Not ideal for

  • A manufacturer-specific marking that is not one of the three standard shapes
  • Confirming tolerance or power rating, which the code does not carry
  • Identifying a part with no readable marking

What this tool keeps

  • The exact code you typed, echoed on the chip drawing
  • A value in ohms and a shortened kΩ or MΩ form
  • The name of the standard that matched

What may need cleanup

  • The decoded value, if the code is a manufacturer variant
  • The unit form, which is a display convenience rather than a measurement
  • A code with letters outside the EIA-96 suffixes, which is refused

Common errors

  • Reading 1002 as one thousand and two instead of 10 kΩ
  • Treating a leading zero in a numeric code as a significant figure
  • Assuming the page validates the part against a stock list

Example use cases

  • Repair work on a board with unlabelled parts
  • A study exercise on EIA-96 codes
  • Checking a resistor value in a parts drawer

Sample input

The three-character code 103 typed into the marking field.

Sample output

A resistance of 10 kΩ, reported as the 3-digit standard with the ohm value and the code drawn on the chip.

Who this is for

  • Electronics hobbyists
  • Repair technicians
  • Students learning component markings

Frequently asked questions

How are surface-mount resistor codes read?

Three- and four-digit codes use the last digit as a power of ten, a letter R marks a decimal point, and a two-digit-plus-letter code is read from the EIA-96 table.

Does the code carry tolerance or power rating?

No. Those are not part of the marking, so the decode cannot confirm them.

Why was my code refused?

A marking that is not one of the three standard shapes, or has letters outside the EIA-96 suffixes, is refused rather than guessed.

Developer program

Build custom tools for your store

Join the SDK program to create useful ecommerce utilities for your store.