Pressure Calculator screenshot

Pressure Calculator

Pressure from a force and the area it acts on, printed in pascals and kilopascals.

Privacy First
0 Runs
Updated 2026-11-21
Runs in your browser
No sign-up, no upload

What the pressure calculator does

It applies P = F / A, one pair per line, in pascals with the same figure in kilopascals beside it. 100 N over 0.05 m² is 2000 Pa, which is 2 kPa.

The area is the area the force is spread over, so a narrow contact gives a higher pressure for the same force. The page assumes the force is spread evenly; a real contact is rarely uniform, which the page states instead of implying a local pressure field.

A zero area is refused because the division would have no value, a negative area is refused as impossible, and a negative force is refused because the page prints a magnitude. Up to 1000 pairs are accepted.

Numbers print to ten significant figures with trailing zeros trimmed.

How to use it

Enter one force, area pair per line in the text box, in newtons and square metres.

Press Run. Each line prints the pressure in pascals and kilopascals. Square millimetres must be converted to square metres first, because the page does no unit conversion.

Worked example

Input:

100, 0.05

Output:

Line 1:  2000 Pa = 2 kPa

Why it runs in your browser

The division runs on this page with JavaScript. Nothing you type is uploaded.

Pressure is force spread over an area, and the page computes P = F / A from the two values you measured. It prints the answer in pascals with the same figure in kilopascals beside it.

A force of 100 N over 0.05 m² is 2000 Pa, which is 2 kPa. Halving the area doubles the pressure for the same force, which is why a narrow contact is the one that marks a surface.

The page assumes the force is spread evenly over the area. A real contact is rarely uniform, and the copy says so rather than implying a local pressure field.

What a pascal is

One pascal is one newton per square metre. It is a small unit, which is why a kilopascal is 1000 Pa and why engineering figures are often quoted in kPa, bar or psi — none of which the page converts to, because each is a unit conversion rather than a different calculation.

The area is the contact area, not the object's surface area. A 100 N load on four feet shares the force between them, so each foot carries a quarter of it over its own area; the page evaluates one force over one area per line.

Uniform pressure is an assumption

Dividing a force by an area gives the average pressure. A tyre's contact patch, a knife edge and a chair leg all carry a distribution, and the peak can be much higher than the average. The page prints the average and names the assumption.

For a fluid at rest the pressure is isotropic and the same quotient is the hydrostatic pressure at a depth; for a solid contact it is an average over the area you supply. The page does not distinguish the two, because the arithmetic is the same and the assumption is yours.

How to use Pressure Calculator

Enter one `force, area` pair per line in the text box, with the force in newtons and the area in square metres.

Press Run. Each line prints the pressure in pascals and kilopascals.

In the text box, convert square millimetres to square metres first — 1 mm² is 0.000001 m² — because the page performs no unit conversion.

What to Expect

Best for

  • An average pressure from a force and a contact area
  • Comparing two contacts carrying the same load
  • A first check of a pressure figure in pascals

Not ideal for

  • A peak pressure in a non-uniform contact
  • A gauge pressure, which needs the ambient pressure subtracted

What this tool keeps

  • Every pair in the order you entered it
  • Both printed units from the same quotient

What may need cleanup

  • A force in kilograms-force, which has to be converted to newtons
  • An area in square centimetres, which has to be converted to square metres

Common errors

  • Using the object's total surface area instead of the contact area
  • Entering a mass in kilograms where a force in newtons is expected

Example use cases

  • Checking a chair leg's load on a floor
  • A physics exercise on pressure
  • Comparing a wide foot with a narrow one under the same load

Sample input

A force of 100 N over an area of 0.05 m².

Sample output

2000 Pa = 2 kPa.

Who this is for

  • Students learning pressure
  • Anyone checking a load per area

Frequently asked questions

Is this gauge pressure or absolute pressure?

Neither. It is the pressure the force produces over the area, with no ambient subtracted and none added. Gauge pressure would subtract the surrounding pressure, which this page does not know.

Why is the area refused at zero?

Pressure is force divided by area, and division by zero has no value. A zero area is refused with the value named rather than printing infinity.

Does the shape of the contact matter?

Not to this quotient: only the area enters it. The shape decides how the force is distributed, and a sharp edge concentrates it far above the average the page prints.

Can I use pounds and square inches?

Convert them first. The page takes newtons and square metres, so 1 lbf is about 4.448 N and 1 in² is 0.00064516 m². It performs no unit conversion.

Developer program

Build custom tools for your store

Join the SDK program to create useful ecommerce utilities for your store.