Back to Updates

Resize an Image: Common Errors and Fixes

A
Admin
2026-11-15
Last updated 2026-11-15

Quick answer

Four symptoms cover almost every resize problem. Stretched means both dimensions were filled. Soft means the source was smaller than the output. A lost transparent background means the format was JPEG. A surprisingly large file means PNG or a quality setting that was too high. Each is a single decision, and each is cheap to redo from the original.

What this article covers

The failures in the order they appear, what causes each, and the fix. It also covers the cases where a resize is the wrong operation and no setting will help. For a first run, read the beginner's guide.

What it actually does

Resizing has one geometry decision and one encoding decision, and the symptoms map onto them.

Geometry: one dimension preserves the shape, two dimensions choose a new shape, and the fit setting decides whether that shape is honoured by fitting inside the box or by distorting the picture to fill it.

Encoding: the format decides whether transparency survives and whether the compression is lossy, and the quality setting applies only to the lossy formats.

The third factor is the source. A resize cannot create detail, and it cannot recover a transparent background that a previous JPEG pass already flattened.

Step by step

  1. Compare the result with the original at the same zoom, side by side.
  2. Read the file's pixel dimensions and format.
  3. Match the symptom to the list below.
  4. Fix the one decision that produced it and run again from the original.
  5. If the source itself is the problem, fix or replace the source first.

What to check after download

  • Dimensions and format, read from the file properties.
  • Shape, against the original.
  • Sharpness at 100 per cent.
  • Transparency where it existed before.
  • Background colour where a transparent area was filled.
  • File size against the destination's limit.
  • Orientation, for photographs from a phone.

Fixes by symptom

The image is stretched or squashed. Both dimensions were filled and the fit was stretch, or two dimensions were filled without meaning to. Fix: clear one dimension, or choose contain.

The image looks soft. The output is larger than the source, or the source was already compressed. Fix: use a larger source. No setting recovers detail.

The transparent background turned white or black. The output is JPEG, which has no transparency. Fix: choose PNG or WebP.

The file is much larger than expected. PNG on a photograph, or quality at 100. Fix: JPEG or WebP at 90 for a photograph.

The file is smaller than expected and looks blocky. Quality is too low. Fix: raise it in steps of 10 and compare.

The image is rotated differently from the source. The source carries its orientation; a resize does not rotate it. Fix: rotate the source first, then resize.

The dimensions are one pixel off. Rounding of a non-integer aspect ratio. Fix: set the dimension that matters and accept the derived one, or set both and contain.

Part of the image is missing. A crop was applied, not a resize. Resizing changes the pixel grid; it does not remove content. Fix: use a crop tool if a crop was intended.

The image has a coloured band around it. The fit was contain and the destination does not hide the padding, or the source itself has a border. Fix: crop the source to the destination's shape, then resize, rather than fitting into a box.

A logo looks jagged at a small size. It was shrunk from a large raster and the fine edges were averaged away. Fix: resize from the largest clean source, or use a vector original if one exists. A PNG at the display size is still a raster, and very small logos are where that shows.

The file opens in one application but not another. The format is one the second application does not support, usually WebP in an older program. Fix: produce a JPEG or PNG copy for that consumer.

The dimensions look right but the page shows the image at a different size. The layout is scaling the image to fit its slot. Fix: give the slot the width it displays, and check the page at the breakpoint where it looks wrong.

Common beginner mistakes

Fixing a stretch by resizing again. Go back to the source; the stretched file has already lost the correct proportions.

Choosing a format for the size rather than the content. Format is about what the file must represent; size is about the dimensions and the quality.

Replacing the source with the resized copy. The next rendition then has nothing large to start from.

Judging sharpness at fit-to-window. Every image looks acceptable small; check at 100 per cent.

Assuming a resize keeps the file type. A PNG source saved as JPEG changes both the transparency behaviour and the kind of compression, and a logo that looked crisp can develop coloured fringes around thin lines.

When this tool is the right choice

When the destination states pixels and the source has at least that many. If the source is smaller, the honest answer is a larger source or a smaller destination. If the task is to change what is in the picture, a crop is the right operation and this tool is not.

Related tools

PDF Converter produces a page image at a chosen resolution, so a resize starts from enough pixels. If the final images need to become a document, Merge PDF Files is the right operation.

Use this tool

Re-run from the original with one dimension filled on Resize an Image, then compare the shape and the sharpness before you publish.

Next step

If the size is the recurring problem rather than the shape, read best settings by destination and write the numbers into your procedure.

Tags